Skip to content
Inference Systems
Guides/Materials

How much plasterboard do I need? One room, worked out

Measure once, get sheets, bags and litres out. A worked three-room house, the coverage figures that decide the answer, and the rounding that wastes a sheet.

Buying plasterboard by eye goes one of two ways: a trip back to the merchant in the middle of a job, or four sheets in the van at the end of it. Both are avoidable with five minutes and a tape measure, because the arithmetic is not difficult — it is just easy to skip.

The four figures that decide everything

Every quantity on a plastering job comes from three measured numbers and one coverage figure:

Input Typical trade figure Where it comes from
Plasterboard sheet 2.4 m × 1.2 m = 2.88 m² the sheet you actually buy
Plaster coverage about 10 m² per 25 kg bag at 2 mm the bag, not the trade counter
Paint coverage about 10 m² per litre the tin
Waste allowance 10% openings, cuts, breakage

Only the first is a fact. The other three are assumptions, and they matter more than the dimensions do. That is why any take-off sheet worth using has them in one editable block rather than buried in a formula.

Wall area, done properly

Wall area is the perimeter times the height, minus the openings:

walls = 2 × (length + width) × height − openings

The openings deduction is where the money is. A room with a door and two windows loses 3–4 m² of wall, which is more than a sheet.

Worked, for a room 4.2 m by 3.0 m at 2.4 m high with 3.6 m² of openings:

Perimeter 2 × (4.2 + 3.0) = 14.4 m
Wall area 14.4 × 2.4 = 34.56 m²
Less openings 34.56 − 3.6 = 30.96 m²
Ceiling 4.2 × 3.0 = 12.60 m²

Sheets, bags and litres

Boards. Wall area plus waste, divided by sheet area, rounded up:

30.96 × 1.10 = 34.06 m² → ÷ 2.88 = 11.83 → 12 sheets

Plaster. Walls and ceilings are usually skimmed, so both areas go in:

(30.96 + 12.60) = 43.56 m² × 1.10 = 47.92 → ÷ 10 = 4.79 → 5 bags

Paint. Same area, two coats, at 10 m² per litre:

43.56 × 2 = 87.12 → ÷ 10 = 8.71 → 9 litres

At £7.50 a sheet, £9 a bag and £6 a litre, that room is £90 + £45 + £54 = £189 of material over 56.16 m² of surface, or £3.37 a square metre.

Three rooms, and why the rounding matters

Room Floor Walls net Ceiling Sheets Bags Litres
Living room 4.2 × 3.0 12.60 30.96 12.60 12 5 9
Bedroom 3.6 × 3.6 12.96 32.16 12.96 13 5 10
Bathroom 2.7 × 2.1 5.67 21.24 5.67 9 3 6
Total 31.23 84.36 31.23 34 13 25

Round each room separately and the job needs 34 sheets, 13 bags and 25 litres. Round once over the totals — which is what you do when you buy for the whole job in one trip — and it is 33 sheets, 13 bags and 24 litres, because the part-sheets from three rooms are still sheets. Same house, one sheet and one litre different, and the difference is whether the rounding happened at the right level.

The traps that cost a merchant trip

Ceiling height equals sheet length. At 2.4 m ceilings, a 2.4 m sheet stands up with nothing to spare. Skirting, an uneven floor and a bowed ceiling mean a sliver comes off almost every sheet, so the practical waste on walls is nearer 15% than 10%. Set the waste figure to what your jobs actually lose, not to the tidy number.

Coverage is a claim on the bag. A 25 kg bag of finishing plaster at 2 mm covers about 10 m². Lay it on at 3 mm and it covers 7 m², and the job runs short in the last room. Bigger bags and backing coats have their own figures — read the bag, not the habit.

New plaster drinks paint. A mist coat on bare plaster is not one of the two finish coats, and it uses roughly a third of a full coat. Two coats over new board is often three in practice, particularly over patch repairs.

Openings are not just windows. Socket boxes, radiator pipes and a chimney breast all change the wall area. Measuring the room and forgetting the chimney is the classic one-room-short error.

Boards only cover the walls. If a ceiling is being overboarded or replaced as well, its area has to be boarded too, not just skimmed. The sheet above boards walls only — change it if the job is different.

Waste is not free. Over-ordering is not a neutral mistake: plasterboard is bulky, damaged by being stacked badly, and leftover sheets are business waste with a duty of care attached to how they are disposed of. See GOV.UK — disposing of business waste.

Doing it once, properly

Measure every room on one sheet of paper: length, width, height, openings. Then apply the rates once. Fifteen minutes at the start of a job is the difference between ordering 33 sheets and ordering 30, going back for three, and paying twice for delivery.

The numbers above are typical trade figures, not your merchant’s prices, and a take-off is not a quote — labour, access, scaffolding and preliminaries are not in it. It tells you what the job consumes.

The plasterboard calculator does this arithmetic for you, room by room, and shows every rate it used. The spreadsheet does the same over up to twelve rooms at once, with your own rates saved, and a cost per square metre from the prices you enter.

General information only, not tax or financial advice. Every guide links to the current GOV.UK page for the rules it applies.